PenangAPRS Track

My position About ☰

reset

VE7XAK-12 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VE7XAK-12. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Battery*	Temp*
1735269227	14.11 Volts	33.94 Deg.C
1735269144	14.2 Volts	33.45 Deg.C
1735269085	14.2 Volts	33.45 Deg.C
1735269036	14.2 Volts	32.96 Deg.C
1735269017	14.17 Volts	32.96 Deg.C
1735268995	14.14 Volts	32.96 Deg.C
1735268953	14.2 Volts	32.96 Deg.C
1735268898	14.2 Volts	32.48 Deg.C
1735268856	14.14 Volts	32.48 Deg.C
1735268824	14.2 Volts	31.5 Deg.C
1735268804	14.17 Volts	31.5 Deg.C
1735268774	14.14 Volts	31.5 Deg.C
1735268732	14.17 Volts	31.5 Deg.C
1735268710	14.17 Volts	31.5 Deg.C
1735268670	14.08 Volts	31.01 Deg.C
1735268629	14.11 Volts	30.52 Deg.C
1735268549	14.14 Volts	30.03 Deg.C
1735268468	14.2 Volts	29.05 Deg.C
1735268441	14.2 Volts	29.05 Deg.C
1735268381	14.14 Volts	27.59 Deg.C
1735268363	14.2 Volts	27.59 Deg.C
1735268358	14.2 Volts	27.1 Deg.C
1735268297	14.17 Volts	26.12 Deg.C
1735268221	14.14 Volts	24.16 Deg.C
1735268200	14.2 Volts	23.67 Deg.C

*Used Equation Coefficients:

Battery: 0, 0.0299, 0

Temp: 0, 0.489, -273.15

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)