PenangAPRS Track

My position About ☰

reset

SP9WJ-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP9WJ-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	temp*	humidity*	v*	Value5*
1735142920	128 C	94 %	53 V	209 V
1735142577	128 C	94 %	53 V	209 V
1735142294	128 C	93 %	53 V	209 V
1735141971	128 C	93 %	53 V	209 V
1735141673	128 C	93 %	53 V	209 V
1735141333	128 C	92 %	53 V	209 V
1735141057	128 C	92 %	53 V	209 V
1735140710	128 C	92 %	53 V	209 V
1735140433	128 C	91 %	53 V	209 V
1735140106	128 C	91 %	53 V	209 V
1735139188	128 C	89 %	54 V	209 V
1735138568	128 C	88 %	54 V	209 V
1735137957	129 C	87 %	54 V	209 V
1735137329	129 C	84 %	54 V	209 V
1735136723	129 C	83 %	54 V	209 V
1735135473	130 C	82 %	54 V	209 V
1735134855	130 C	82 %	55 V	209 V
1735134237	130 C	81 %	55 V	209 V
1735133622	130 C	81 %	55 V	209 V
1735133000	130 C	80 %	54 V	209 V
1735132384	130 C	79 %	55 V	209 V
1735131766	130 C	79 %	55 V	209 V
1735131154	130 C	78 %	55 V	209 V
1735130533	130 C	78 %	55 V	209 V
1735129295	130 C	77 %	55 V	209 V

*Used Equation Coefficients:

current: 0, 0, 0

temp: 0, 1, 0

humidity: 0, 1, 0

v: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)