PenangAPRS Track

My position About ☰

reset

KA6PRW-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KA6PRW-9. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Battery*	Temp*
1794332005	13.51 Volts	17.32 Deg.C
1794332000	13.51 Volts	17.32 Deg.C
1794331885	13.54 Volts	16.34 Deg.C
1794331879	13.48 Volts	16.34 Deg.C
1794331860	13.51 Volts	16.34 Deg.C
1794331282	13.68 Volts	13.89 Deg.C
1794331071	13.8 Volts	12.43 Deg.C
1794331041	13.86 Volts	12.43 Deg.C
1794331021	13.83 Volts	11.94 Deg.C
1794330960	13.86 Volts	11.45 Deg.C
1794330847	13.89 Volts	10.47 Deg.C
1794330801	13.98 Volts	9.98 Deg.C
1794330706	13.98 Volts	8.51 Deg.C
1794330690	13.95 Volts	8.51 Deg.C
1794330671	13.89 Volts	8.03 Deg.C
1794326136	13.95 Volts	6.07 Deg.C
1794252725	13.33 Volts	26.61 Deg.C
1794252713	13.42 Volts	26.61 Deg.C
1794252706	13.39 Volts	26.12 Deg.C
1794252693	13.42 Volts	26.12 Deg.C
1794252654	13.42 Volts	26.12 Deg.C
1794252492	13.39 Volts	26.12 Deg.C
1794252339	13.57 Volts	25.63 Deg.C
1794252335	13.54 Volts	25.63 Deg.C
1794252329	13.57 Volts	25.63 Deg.C

*Used Equation Coefficients:

Battery: 0, 0.0293, 0

Temp: 0, 0.489, -273.15

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)