PenangAPRS Track

My position About ☰

reset

VK2RF-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK2RF-9. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Value1*	Value2*
1786508354	14.01 Volts	29.05 Deg.C
1786508329	13.95 Volts	29.05 Deg.C
1786508275	14.03 Volts	28.56 Deg.C
1786508211	13.95 Volts	27.59 Deg.C
1786508157	13.92 Volts	27.1 Deg.C
1786507972	13.92 Volts	22.21 Deg.C
1786497272	13.68 Volts	31.5 Deg.C
1786497213	13.83 Volts	30.52 Deg.C
1786497190	13.8 Volts	30.03 Deg.C
1786497084	13.92 Volts	30.03 Deg.C
1786497047	13.95 Volts	29.54 Deg.C
1786496896	13.98 Volts	28.56 Deg.C
1786496791	14.09 Volts	27.59 Deg.C
1786496716	13.89 Volts	26.61 Deg.C
1786496695	13.89 Volts	26.12 Deg.C
1786496672	13.95 Volts	24.65 Deg.C
1786494155	13.95 Volts	33.45 Deg.C
1786494136	14.06 Volts	32.96 Deg.C
1786494089	13.83 Volts	31.5 Deg.C
1786493979	14.18 Volts	31.5 Deg.C
1786493865	13.6 Volts	31.01 Deg.C
1786493662	11.66 Volts	30.52 Deg.C
1786493302	11.72 Volts	30.03 Deg.C
1786492072	14.01 Volts	28.56 Deg.C
1786492028	13.98 Volts	27.59 Deg.C

*Used Equation Coefficients:

Value1: 0, 0.0293, 0

Value2: 0, 0.489, -273.15

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)