PenangAPRS Track

My position About ☰

reset

F1EDJ-7 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object F1EDJ-7. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	V_Batt*	Value2*	Value3*	Value4*	Value5*
1736702340	2.67 VDC	0	0	0	0
1736702314	2.67 VDC	0	0	0	0
1736702229	2.67 VDC	0	0	0	0
1736702205	2.67 VDC	0	0	0	0
1736702136	2.66 VDC	0	0	0	0
1736702051	2.68 VDC	0	0	0	0
1736701729	2.67 VDC	0	0	0	0
1736701666	2.69 VDC	0	0	0	0
1736701603	2.7 VDC	0	0	0	0
1736701528	2.7 VDC	0	0	0	0
1736701450	2.71 VDC	0	0	0	0
1736701347	2.67 VDC	0	0	0	0
1736701324	2.67 VDC	0	0	0	0
1736701301	2.7 VDC	0	0	0	0
1736701238	2.71 VDC	0	0	0	0
1736701142	2.7 VDC	0	0	0	0
1736679257	2.91 VDC	0	0	0	0
1736679193	2.91 VDC	0	0	0	0
1736679171	2.9 VDC	0	0	0	0
1736679108	2.91 VDC	0	0	0	0
1736679028	2.9 VDC	0	0	0	0
1736678825	2.91 VDC	0	0	0	0
1736678395	2.92 VDC	0	0	0	0
1736678272	2.9 VDC	0	0	0	0
1736678208	2.92 VDC	0	0	0	0

*Used Equation Coefficients:

V_Batt: 0, 0.01, 0

Value2: 0, 1, 0

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)