PenangAPRS Track

My position About ☰

reset

KC2G Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KC2G. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	BatTemp*	Bat*	Solar*
1764981862	29 deg.F	12.95 V	10 V
1764981861	29 deg.F	12.95 V	10 V
1764980962	29 deg.F	12.95 V	10 V
1764980961	29 deg.F	12.95 V	10 V
1764980062	29 deg.F	12.95 V	10 V
1764980060	29 deg.F	12.95 V	10 V
1764979162	29 deg.F	12.95 V	10 V
1764979160	29 deg.F	12.95 V	10 V
1764978260	29 deg.F	12.95 V	10 V
1764977362	29 deg.F	12.95 V	10 V
1764977361	29 deg.F	12.95 V	10 V
1764976463	29 deg.F	12.95 V	10 V
1764976460	29 deg.F	12.95 V	10 V
1764975561	29 deg.F	12.95 V	10 V
1764974663	29 deg.F	12.95 V	10 V
1764974660	29 deg.F	12.95 V	10 V
1764973765	29 deg.F	12.95 V	10 V
1764973761	29 deg.F	12.95 V	10 V
1764972862	29 deg.F	12.95 V	10 V
1764972860	29 deg.F	12.95 V	10 V
1764971962	29 deg.F	12.95 V	10 V
1764971961	29 deg.F	12.95 V	10 V
1764971062	29 deg.F	12.95 V	10 V
1764971060	29 deg.F	12.95 V	10 V
1764970165	29 deg.F	12.95 V	11.75 V

*Used Equation Coefficients:

BatTemp: 0, 0.5, 0

Bat: 0, 0.05, 10

ChgA: 0, 0.05, 0

Solar: 0, 0.05, 10

Chg: 0.002, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)