PenangAPRS Track

My position About ☰

reset

VE7EOL-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VE7EOL-2. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Battery*	Temp*
1773777595	13.07 Volts	33.94 Deg.C
1773777591	13.04 Volts	33.45 Deg.C
1773777547	13.1 Volts	33.94 Deg.C
1773777542	13.07 Volts	34.43 Deg.C
1773777515	13.1 Volts	34.43 Deg.C
1773777507	13.16 Volts	34.43 Deg.C
1773777502	13.07 Volts	34.92 Deg.C
1773777409	13.13 Volts	36.39 Deg.C
1773777407	13.1 Volts	35.9 Deg.C
1773777397	13.07 Volts	35.9 Deg.C
1773777370	13.19 Volts	35.9 Deg.C
1773777348	13.21 Volts	35.41 Deg.C
1773777343	13.19 Volts	35.41 Deg.C
1773777336	13.19 Volts	34.92 Deg.C
1773777334	13.21 Volts	34.92 Deg.C
1773777332	13.16 Volts	34.92 Deg.C
1773777304	13.27 Volts	33.94 Deg.C
1773777184	13.3 Volts	30.03 Deg.C
1773777166	13.36 Volts	29.05 Deg.C
1773777161	13.21 Volts	28.56 Deg.C
1773777104	13.45 Volts	25.63 Deg.C
1773777103	13.45 Volts	25.63 Deg.C
1773777097	13.39 Volts	25.14 Deg.C
1773777077	13.33 Volts	25.14 Deg.C
1773777077	13.33 Volts	24.65 Deg.C

*Used Equation Coefficients:

Battery: 0, 0.0293, 0

Temp: 0, 0.489, -273.15

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)