PenangAPRS Track

My position About ☰

reset

VK2BLS-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK2BLS-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Battery*	Temp*
1790310419	12.01 Volts	24.92 Deg.C
1790310115	12.01 Volts	24.92 Deg.C
1790309214	12.01 Volts	25.41 Deg.C
1790308910	12.01 Volts	25.41 Deg.C
1790308009	12.01 Volts	25.41 Deg.C
1790307705	12.04 Volts	25.41 Deg.C
1790306497	12.01 Volts	25.41 Deg.C
1790305596	12.01 Volts	25.41 Deg.C
1790304695	12.04 Volts	25.9 Deg.C
1790303794	12.04 Volts	26.39 Deg.C
1790302893	12.1 Volts	27.37 Deg.C
1790301991	13.33 Volts	28.83 Deg.C
1790301938	13.27 Volts	28.83 Deg.C
1790301923	13.3 Volts	28.34 Deg.C
1790301903	13.3 Volts	28.34 Deg.C
1790301880	13.3 Volts	28.34 Deg.C
1790301820	13.27 Volts	28.34 Deg.C
1790301797	13.21 Volts	27.85 Deg.C
1790301782	13.27 Volts	27.85 Deg.C
1790301646	13.27 Volts	28.34 Deg.C
1790301590	13.33 Volts	28.34 Deg.C
1790301576	13.3 Volts	27.85 Deg.C
1790301557	13.3 Volts	27.85 Deg.C
1790301540	13.27 Volts	27.85 Deg.C
1790301505	13.27 Volts	27.37 Deg.C

*Used Equation Coefficients:

Battery: 0, 0.0293, 0

Temp: 0, 0.489, -283.15

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)