PenangAPRS Track

My position About ☰

reset

VE7EOL-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VE7EOL-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Battery*	Temp*
1790284599	13.86 Volts	37.37 Deg.C
1790284566	13.89 Volts	37.37 Deg.C
1790284557	13.92 Volts	37.37 Deg.C
1790284515	14.03 Volts	37.37 Deg.C
1790284509	13.65 Volts	37.37 Deg.C
1790284406	13.89 Volts	37.37 Deg.C
1790284312	13.95 Volts	37.37 Deg.C
1790284307	13.77 Volts	37.37 Deg.C
1790284300	13.83 Volts	37.37 Deg.C
1790284262	13.8 Volts	37.85 Deg.C
1790284225	13.8 Volts	37.85 Deg.C
1790284206	13.89 Volts	37.85 Deg.C
1790284176	14.06 Volts	37.85 Deg.C
1790284019	14.15 Volts	37.85 Deg.C
1790283993	13.92 Volts	37.37 Deg.C
1790283955	14.03 Volts	36.88 Deg.C
1790283941	14.12 Volts	36.88 Deg.C
1790283935	14.03 Volts	36.88 Deg.C
1790283846	14.12 Volts	35.41 Deg.C
1790283834	13.86 Volts	35.41 Deg.C
1790283167	14.01 Volts	33.94 Deg.C
1790283127	14.3 Volts	33.45 Deg.C
1790283121	13.8 Volts	33.45 Deg.C
1790283103	13.89 Volts	32.96 Deg.C
1790283041	13.86 Volts	31.99 Deg.C

*Used Equation Coefficients:

Battery: 0, 0.0293, 0

Temp: 0, 0.489, -273.15

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)