PenangAPRS Track

My position About ☰

reset

SQ9MTW-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SQ9MTW-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Sate*	Temp*	Pa*	Volt*
1735099308	9	26.5 C	1000 hPa	6.3 V
1735097782	9	26.5 C	1000 hPa	6.3 V
1735096261	9	26.5 C	1000 hPa	6.3 V
1735094741	9	26.6 C	999 hPa	6.6 V
1735093219	9	26.6 C	999 hPa	6.3 V
1735091691	9	26.6 C	999 hPa	6.3 V
1735090170	9	26.6 C	999 hPa	6.6 V
1735088643	9	26.5 C	999 hPa	6.6 V
1735087125	9	26.6 C	998 hPa	6.3 V
1735084085	9	26.5 C	998 hPa	6.3 V
1735082560	8	26.6 C	998 hPa	6.6 V
1735081042	9	26.6 C	998 hPa	6.6 V
1735079514	8	26.6 C	997 hPa	6.6 V
1735077996	8	26.6 C	997 hPa	6.6 V
1735074944	10	26.6 C	996 hPa	6.3 V
1735073418	8	26.6 C	996 hPa	6.3 V
1735071894	10	26.6 C	996 hPa	6.8 V
1735070372	9	26.6 C	995 hPa	6.3 V
1735068846	9	26.6 C	995 hPa	6.6 V
1735067320	9	26.7 C	995 hPa	6.6 V
1735065797	7	26.7 C	995 hPa	6.6 V
1735064272	9	26.6 C	994 hPa	6.3 V
1735062749	8	26.6 C	994 hPa	6.8 V
1735061224	9	26.6 C	994 hPa	6.3 V
1735059706	11	26.6 C	993 hPa	6.6 V

*Used Equation Coefficients:

Sate: 0, 1, 0

Temp: 0, 0.1, -50

Pa: 0, 1, 0

Volt: 0, 0.1, 0

--: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)