PenangAPRS Track

My position About ☰

reset

W6SRR-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object W6SRR-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	DC*	PC Board*	CPU*	Ambient*
1786398408	1356	91	40.8	82.8
1786397510	1356	91	40.2	82.8
1786396609	1354	90.8	41.3	82.6
1786395710	1356	90.8	40.8	82.6
1786394807	1356	90.8	40.8	82.8
1786393911	1356	90.8	40.8	82.7
1786393009	1356	90.6	39.7	82.4
1786392111	1356	90.6	40.2	82.6
1786391208	1356	90.6	40.2	82.6
1786390311	1360	90.5	39.7	82.3
1786389409	1356	90.4	39.7	82.4
1786388509	1356	90.5	40.8	82.6
1786387608	1356	90.3	40.2	82.4
1786386709	1356	90.2	40.2	82.2
1786385809	1356	90.3	39.7	82.4
1786384910	1356	90.3	39.7	82.2
1786384008	1356	90.1	40.2	82.3
1786383110	1356	90.2	39.7	82.4
1786382209	1356	90.1	40.2	82.1
1786381310	1356	90.1	39.7	82.3
1786380408	1356	89.9	39.7	81.8
1786379512	1356	89.9	39.7	82.2
1786378609	1356	89.9	39.7	82
1786377710	1356	89.7	39.7	82
1786376808	1356	89.8	40.2	82.2

*Used Equation Coefficients:

DC: 0, 1, 1000

PC Board: 0, 0.1, 0

CPU: 0, 0.1, 0

Ambient: 0, 0.1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)