PenangAPRS Track

My position About ☰

reset

DC4HF-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DC4HF-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Value1*	Value2*	Value3*	Value4*	Value5*
1794329902	1377	5717	7412	3475	3976
1794329002	1377	5733	7417	3492	4002
1794328100	1377	5734	7414	3545	3928
1794327200	1377	5743	7420	3567	3960
1794326298	1377	5742	7421	3632	3886
1794325398	1377	5744	7422	3644	3964
1794324496	1377	5748	7425	3682	3937
1794323596	1377	6711	7423	3785	3672
1794322665	1377	6731	7410	3552	3968
1794321761	1377	5647	7406	3270	4197
1794320860	1377	5651	7406	3278	4203
1794319959	1377	5653	7408	3284	4209
1794319058	1377	5656	7411	3291	4213
1794318157	1377	5662	7414	3296	4216
1794317256	1377	5667	7413	3302	4220
1794316355	1377	5667	7414	3306	4228
1794315454	1377	5668	7414	3311	4227
1794314553	1377	5667	7407	3317	4230
1794313652	1377	5671	7411	3321	4241
1794312751	1377	5674	7409	3325	4248
1794311850	1377	5676	7409	3329	4257
1794310949	1377	5677	7411	3329	4259
1794310048	1377	5678	7409	3329	4267
1794309147	1377	5680	7411	3328	4272
1794308246	1377	5681	7406	3326	4280

*Used Equation Coefficients:

Value1: 0, 1, 0

Value2: 0, 1, 0

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)