PenangAPRS Track

My position About ☰

reset

WA6ODP-4 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object WA6ODP-4. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Value1*	Value2*	Value3*	Value4*
1735134002	1389	51.5	27.9	42.5
1735133102	1389	51.4	27.9	42.5
1735132202	1389	51.5	27.9	42.5
1735131304	1389	51.5	27.9	42.6
1735130402	1389	51.6	27.9	42.6
1735129502	1389	51.7	27.9	42.7
1735128602	1390	51.8	27.9	42.8
1735127703	1390	51.9	27.9	43
1735126802	1390	51.9	27.9	43
1735125902	1390	51.7	27.9	42.9
1735117801	1391	51.1	27.3	42.1
1735116905	1392	51.2	27.9	42.1
1735116001	1392	51.4	27.3	42.1
1735115101	1392	51.8	27.9	42.6
1735114201	1393	52.1	28.4	43.1
1735113304	1392	52.4	27.9	43.4
1735112401	1393	52.5	28.4	43.5
1735111501	1393	52.2	27.9	43.7
1735110601	1392	52	27.9	43.4
1735109702	1394	51.7	27.9	42.8
1735108801	1394	51.6	27.9	42.7
1735107902	1394	51.7	27.9	42.8
1735107001	1395	51.5	27.9	42.8
1735106102	1395	51.2	27.9	42.5
1735105201	1395	51.5	27.9	42.4

*Used Equation Coefficients:

Value1: 0, 1, 1000

Value2: 0, 0.1, 0

Value3: 0, 0.1, 0

Value4: 0, 0.1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)