PenangAPRS Track

My position About ☰

reset

YC1SNI Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YC1SNI. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Temp.*	Humidity*	Voltage*
1786441959	30 °C	56 %RH	4 V
1786441945	30 °C	56 %RH	4 V
1786441381	30 °C	55 %RH	4 V
1786439626	31 °C	54 %RH	4 V
1786437871	29 °C	59 %RH	4 V
1786436116	29 °C	58 %RH	4 V
1786434361	29 °C	58 %RH	4 V
1786434347	29 °C	58 %RH	4 V
1786433191	29 °C	58 %RH	4 V
1786431436	29 °C	58 %RH	4 V
1786429681	29 °C	59 %RH	4 V
1786427926	29 °C	59 %RH	4 V
1786426171	28 °C	56 %RH	4 V
1786425980	28 °C	57 %RH	4 V
1786425026	28 °C	56 %RH	4 V
1786423271	28 °C	57 %RH	4 V
1786421516	28 °C	59 %RH	4 V
1786419761	29 °C	66 %RH	4 V
1786418006	29 °C	64 %RH	4 V
1786416251	29 °C	64 %RH	4 V
1786414496	29 °C	64 %RH	4 V
1786412741	29 °C	63 %RH	4 V
1786410986	29 °C	59 %RH	4 V
1786409231	29 °C	65 %RH	4 V
1786407476	29 °C	69 %RH	4 V

*Used Equation Coefficients:

Temp.: 0, 1, 0

Humidity: 0, 1, 0

Voltage: 0, 1, 0

Current: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)