PenangAPRS Track

My position About ☰

reset

HS8AC-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HS8AC-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TEMP*	HUM*	VBAT*
1782639184	28.2 °C	0 %RH	4.2 V
1782638584	27.62 °C	0 %RH	4.21 V
1782637984	27.29 °C	0.3 %RH	4.2 V
1782637384	27.83 °C	0 %RH	4.21 V
1782636784	27.76 °C	3.9 %RH	4.2 V
1782636184	28.49 °C	4.7 %RH	4.21 V
1782635584	29.56 °C	5.9 %RH	4.2 V
1782634984	28.39 °C	14.7 %RH	4.2 V
1782634384	26.55 °C	3.8 %RH	4.21 V
1782633784	28.8 °C	100 %RH	4.21 V
1782633184	35.13 °C	82.2 %RH	4.21 V
1782632584	32.14 °C	89.3 %RH	4.21 V
1782631984	33.04 °C	83.9 %RH	4.21 V
1782631384	34.22 °C	81.9 %RH	4.21 V
1782630784	33.98 °C	80.2 %RH	4.21 V
1782630184	33.45 °C	82.7 %RH	4.21 V
1782629584	32.97 °C	84.3 %RH	4.21 V
1782628984	35.93 °C	74.9 %RH	4.21 V
1782628384	34.12 °C	82.5 %RH	4.21 V
1782627784	33.73 °C	81.4 %RH	4.21 V
1782627184	35.31 °C	76.7 %RH	4.21 V
1782626584	36.38 °C	77.5 %RH	4.21 V
1782625984	33.36 °C	82.7 %RH	4.21 V
1782625384	33.08 °C	81.9 %RH	4.21 V
1782624784	34.45 °C	83.3 %RH	4.21 V

*Used Equation Coefficients:

TEMP: 0, 0.01, 0

HUM: 0, 0.1, 0

VBAT: 0, 0.01, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)