PenangAPRS Track

My position About ☰

reset

HS8AS-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HS8AS-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TEMP*	HUM*	VBAT *
1782646924	27.53 °C	84.4 %RH	4 V
1782646324	27.75 °C	83.2 %RH	4 V
1782645724	28.51 °C	81.6 %RH	4 V
1782645124	29.03 °C	80.3 %RH	4 V
1782644524	29.53 °C	78.2 %RH	4 V
1782643924	29 °C	79.6 %RH	4 V
1782643324	29.36 °C	78.6 %RH	4.01 V
1782642724	29.46 °C	80.4 %RH	4 V
1782642124	29.48 °C	76.5 %RH	4.01 V
1782641524	29.58 °C	77.6 %RH	4 V
1782640924	30.29 °C	74.6 %RH	4 V
1782640324	31.31 °C	69.5 %RH	4 V
1782639724	29.95 °C	74.9 %RH	4 V
1782639124	29.09 °C	76.8 %RH	4 V
1782638524	29.3 °C	76.2 %RH	4 V
1782637924	29.51 °C	76.1 %RH	4 V
1782637324	29.63 °C	73.9 %RH	4 V
1782636724	28.64 °C	77 %RH	4.01 V
1782636124	29.03 °C	78 %RH	4.01 V
1782635524	30.7 °C	69.5 %RH	4 V
1782634924	29.03 °C	78.7 %RH	4.01 V
1782634324	28.49 °C	79.9 %RH	4 V
1782633724	27.62 °C	82 %RH	4 V
1782633124	28.21 °C	84.8 %RH	4.01 V
1782632524	27.58 °C	86.1 %RH	4.01 V

*Used Equation Coefficients:

TEMP: 0, 0.01, 0

HUM: 0, 0.1, 0

VBAT : 0, 0.01, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)