PenangAPRS Track

My position About ☰

reset

YB1LZ-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YB1LZ-9. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Temp.*	Humidity*	Pressure*
1794341019	31 °C	48 %RH	935 hPa
1794339362	31 °C	47 %RH	935 hPa
1794337705	31 °C	47 %RH	935 hPa
1794336048	31 °C	47 %RH	935 hPa
1794334391	31 °C	48 %RH	936 hPa
1794332734	31 °C	48 %RH	936 hPa
1794331077	31 °C	48 %RH	936 hPa
1794329420	31 °C	48 %RH	937 hPa
1794327763	32 °C	47 %RH	936 hPa
1794326105	32 °C	47 %RH	937 hPa
1794324448	32 °C	48 %RH	937 hPa
1794322791	32 °C	48 %RH	937 hPa
1794321134	32 °C	45 %RH	937 hPa
1794319477	33 °C	43 %RH	936 hPa
1794317820	33 °C	42 %RH	936 hPa
1794316163	33 °C	42 %RH	936 hPa
1794314506	33 °C	42 %RH	936 hPa
1794312849	33 °C	42 %RH	935 hPa
1794311192	33 °C	43 %RH	935 hPa
1794309535	32 °C	44 %RH	934 hPa
1794307878	32 °C	44 %RH	934 hPa
1794306221	32 °C	43 %RH	934 hPa
1794304564	33 °C	42 %RH	933 hPa
1794302907	34 °C	41 %RH	933 hPa
1794301250	37 °C	35 %RH	933 hPa

*Used Equation Coefficients:

Temp.: 0, 1, 0

Humidity: 0, 1, 0

Pressure: 0, 1, 0

AllCount: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)