PenangAPRS Track

My position About ☰

reset

SP2ROC-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP2ROC-13. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	RPM*	VBAT*	TEMP*	MTH*
1794332063	685 rpm	12.57 V	32 degC	78 h
1794332033	684 rpm	12.57 V	30 degC	78 h
1794332003	695 rpm	12.55 V	28 degC	78 h
1794331973	696 rpm	12.55 V	26 degC	78 h
1794331943	865 rpm	12.55 V	23 degC	78 h
1794331913	867 rpm	12.5 V	21 degC	78 h
1794331883	869 rpm	12.55 V	19 degC	78 h
1794331853	869 rpm	12.5 V	18 degC	78 h
1794331823	883 rpm	12.49 V	16 degC	78 h
1794331793	895 rpm	12.49 V	16 degC	78 h
1794331763	907 rpm	12.48 V	15 degC	78 h
1794331733	956 rpm	12.37 V	15 degC	78 h
1794331703	0 rpm	12.47 V	16 degC	78 h
1794331673	0 rpm	12.39 V	16 degC	78 h
1794326132	124 rpm	12.22 V	29 degC	78 h
1794326102	0 rpm	12.33 V	29 degC	78 h
1794326072	0 rpm	12.41 V	29 degC	78 h
1794326033	0 rpm	12.38 V	29 degC	78 h
1794326003	0 rpm	12.33 V	29 degC	78 h
1794325972	0 rpm	12.39 V	30 degC	78 h
1794325942	0 rpm	12.31 V	30 degC	78 h
1794325912	0 rpm	12.33 V	30 degC	78 h
1794325882	0 rpm	12.5 V	30 degC	78 h
1794325852	0 rpm	12.48 V	30 degC	78 h
1794325822	232 rpm	9.46 V	30 degC	78 h

*Used Equation Coefficients:

RPM: 0, 1, 0

VBAT: 0, 0.01, 0

TEMP: 0, 1, -100

TRIP: 0, 0.1, 0

MTH: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)