PenangAPRS Track

My position About ☰

reset

OK4AB-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OK4AB-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temperatu*	Humidity*	Pressure*	Satellite*
1770414814	27.37 C	41.51 %	959 hPa	6
1770414765	27.38 C	41.5 %	959 hPa	6
1770414761	27.38 C	41.53 %	959 hPa	6
1770414742	27.38 C	41.51 %	959 hPa	7
1770414703	27.38 C	41.53 %	959 hPa	6
1770414685	27.38 C	41.53 %	959 hPa	6
1770414647	27.38 C	41.71 %	959 hPa	7
1770414643	27.38 C	41.54 %	959 hPa	7
1770414588	27.38 C	41.54 %	959 hPa	7
1770414583	27.38 C	41.53 %	959 hPa	7
1770414523	27.38 C	41.56 %	959 hPa	7
1770414503	27.38 C	41.55 %	959 hPa	7
1770414471	27.39 C	41.57 %	959 hPa	7
1770414463	27.39 C	41.55 %	959 hPa	7
1770414439	27.38 C	41.57 %	958.9 hPa	7
1770414417	27.38 C	41.57 %	958.9 hPa	5
1770414407	27.38 C	41.57 %	958.9 hPa	5
1770414399	27.38 C	41.57 %	958.9 hPa	5
1770414373	27.38 C	41.58 %	958.9 hPa	7
1770414353	27.38 C	41.61 %	958.9 hPa	7
1770414344	27.38 C	41.61 %	958.9 hPa	7
1770414340	27.38 C	41.61 %	958.9 hPa	7
1770414306	27.38 C	41.6 %	958.9 hPa	7
1770414293	27.38 C	41.58 %	958.9 hPa	6
1770414284	27.38 C	41.58 %	958.9 hPa	6

*Used Equation Coefficients:

Temperatu: 0, 0.01, 0

Humidity: 0, 0.01, 0

Pressure: 0, 0.1, 800

Battery: 0, 0.01, 0

Satellite: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)