PenangAPRS Track

My position About ☰

reset

F6DEV-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object F6DEV-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	V_Batt*	RX_rate*	RelRate*	DrpRate*
1794340169	4.24 VDC	80 pkt/h	8 pkt/h	72 pkt/h
1794332970	4.23 VDC	89 pkt/h	13 pkt/h	76 pkt/h
1794329369	4.23 VDC	100 pkt/h	19 pkt/h	81 pkt/h
1794325776	4.23 VDC	124 pkt/h	18 pkt/h	106 pkt/h
1794322169	4.23 VDC	163 pkt/h	38 pkt/h	125 pkt/h
1794318556	4.23 VDC	186 pkt/h	37 pkt/h	149 pkt/h
1794314949	4.23 VDC	128 pkt/h	17 pkt/h	111 pkt/h
1794311349	4.23 VDC	136 pkt/h	13 pkt/h	123 pkt/h
1794307749	4.24 VDC	127 pkt/h	10 pkt/h	117 pkt/h
1794300548	4.24 VDC	96 pkt/h	14 pkt/h	83 pkt/h
1794296928	4.23 VDC	117 pkt/h	15 pkt/h	102 pkt/h
1794293328	4.23 VDC	112 pkt/h	15 pkt/h	97 pkt/h
1794289727	4.24 VDC	97 pkt/h	11 pkt/h	86 pkt/h
1794286127	4.23 VDC	95 pkt/h	15 pkt/h	80 pkt/h
1794282527	4.23 VDC	109 pkt/h	15 pkt/h	94 pkt/h
1794278927	4.23 VDC	95 pkt/h	11 pkt/h	85 pkt/h
1794275307	4.23 VDC	96 pkt/h	13 pkt/h	83 pkt/h
1794271713	4.23 VDC	117 pkt/h	14 pkt/h	103 pkt/h
1794268107	4.23 VDC	121 pkt/h	10 pkt/h	111 pkt/h
1794264507	4.23 VDC	112 pkt/h	13 pkt/h	99 pkt/h
1794260906	4.23 VDC	102 pkt/h	14 pkt/h	88 pkt/h
1794257306	4.23 VDC	99 pkt/h	14 pkt/h	86 pkt/h

*Used Equation Coefficients:

V_Batt: 0, 0.01, 0

RX_rate: 0, 1, 0

RelRate: 0, 1, 0

DrpRate: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)