PenangAPRS Track

My position About ☰

reset

HS5TQA-4 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HS5TQA-4. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	VBAT*	IBAT*	SOLAR*
1790179699	13.25 V	52 mA	23.59 V
1790177898	13.27 V	46 mA	23.59 V
1790176098	13.29 V	52 mA	23.59 V
1790174298	13.31 V	51 mA	23.59 V
1790172499	13.34 V	53 mA	23.59 V
1790170698	13.38 V	50 mA	23.59 V
1790168898	13.43 V	50 mA	23.59 V
1790167099	13.48 V	53 mA	23.59 V
1790165748	13.52 V	44 mA	23.59 V
1790163948	13.61 V	53 mA	23.59 V
1790162148	13.71 V	47 mA	23.59 V
1790160348	13.84 V	24 mA	23.59 V
1790158548	13.77 V	51 mA	23.59 V
1790156748	13.94 V	-44 mA	23.59 V
1790154948	13.83 V	43 mA	23.59 V
1790153148	13.79 V	50 mA	23.59 V
1790151348	14.05 V	46 mA	23.59 V
1790149548	13.83 V	47 mA	23.59 V
1790147748	13.76 V	44 mA	23.59 V
1790145938	13.93 V	52 mA	23.59 V
1790144138	13.83 V	50 mA	23.59 V
1790142338	13.76 V	50 mA	23.59 V
1790140538	13.93 V	51 mA	23.59 V
1790138738	13.84 V	52 mA	23.59 V
1790136938	13.78 V	52 mA	23.59 V

*Used Equation Coefficients:

VBAT: 0, 0.01, 0

IBAT: 0, 1, -2000

SOLAR: 0, 0.01, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)