PenangAPRS Track

My position About ☰

reset

VK2HFF-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK2HFF-9. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Temp*	CoreTemp*	FanDC*	BattV*	Batt2_SoC*
1765001773	43 Deg.C	72 Deg.C	25 DutyCyc	13.2 V	100 SoC%
1764999970	43 Deg.C	68 Deg.C	30 DutyCyc	13.3 V	100 SoC%
1764998170	45 Deg.C	71 Deg.C	30 DutyCyc	13.3 V	100 SoC%
1764996370	45 Deg.C	69 Deg.C	42 DutyCyc	14.5 V	100 SoC%
1764994571	45 Deg.C	68 Deg.C	45 DutyCyc	13.3 V	100 SoC%
1764992770	47 Deg.C	70 Deg.C	52 DutyCyc	14.5 V	100 SoC%
1764990970	46 Deg.C	68 Deg.C	52 DutyCyc	14.5 V	100 SoC%
1764989170	45 Deg.C	70 Deg.C	37 DutyCyc	14.5 V	100 SoC%
1764987370	46 Deg.C	69 Deg.C	32 DutyCyc	14.4 V	100 SoC%
1764985572	46 Deg.C	71 Deg.C	32 DutyCyc	14.5 V	100 SoC%
1764983770	43 Deg.C	67 Deg.C	32 DutyCyc	14.4 V	100 SoC%
1764981970	43 Deg.C	69 Deg.C	25 DutyCyc	14.4 V	100 SoC%
1764980169	41 Deg.C	74 Deg.C	80 DutyCyc	14.4 V	100 SoC%
1764980121	44 Deg.C	88 Deg.C	50 DutyCyc	14.4 V	100 SoC%

*Used Equation Coefficients:

Temp: 0, 1, 0

CoreTemp: 0, 1, 0

FanDC: 0, 1, 0

BattV: 0, 0.1, 0

Batt2_SoC: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)